Buy now and Pay Later!
+44 (0) 1543 397 397
All items in Stock & Ready to Ship
[Spare Part] Mosfet for Cyma Platinum Eshooter ETU EMG Daniel Defense (CM.1050DL BK)
Restore maximum response and programmable control to your primary with the Replacement Eshooter ETU MOSFET for the CYMA Platinum EMG Daniel Defense (CM.1050DL BK). Designed as a drop-in internal spare module for CYMA’s latest-generation V2 gearbox platforms, this Electronic Trigger Unit (ETU) directly replaces damaged or burnt-out stock MOSFET boards. Delivering crisp optical trigger detection, fast semi-auto cycling, binary trigger programming, active braking, and low-resistance wiring, it brings your high-performance Daniel Defense AEG straight back into action.
When high-rate-of-fire CYMA Platinum AEGs experience trigger issues, MOSFET failures, or electrical cutouts, replacing the electronic unit is essential to restoring reliability. The Eshooter ETU Spare MOSFET is the direct-fit replacement circuit board engineered specifically for the CYMA Platinum EMG Daniel Defense M4 Series (CM.1050 / CM.1050DL BK) featuring the Eshooter trigger system.
Precision Optical Triggering & Smart Protection
Unlike traditional mechanical trigger contacts that wear down from electrical arcing, the Eshooter ETU utilizes non-contact optical sensors to register every trigger pull. This completely eliminates mechanical drag, drastically shortens trigger reset times, and prevents microswitch breakdown. Integrated microprocessors monitor current flow, motor workload, and voltage supply in real time—automatically isolating the system if an over-current event or low battery voltage is detected to safeguard your motor and battery.
Performance Control & Active Braking
The module features integrated Active Braking technology, stopping the motor immediately after a shot cycle is completed. This prevents double-tapping on semi-automatic mode, relieves spring tension when idle, and reduces gearbox stress. Fitted with high-temp silver-plated Teflon wiring and a pre-soldered Deans (T-Plug) connector, this board handles 7.4V and 11.1V LiPo/LiFe batteries effortlessly while maximizing current delivery to high-torque or high-speed motors.
Key Features & Technical Benefits:
-
Direct-Fit Replacement: Purpose-built for CYMA Platinum V2 gearboxes running the factory Eshooter ETU footprint.
-
Non-Contact Optical Sensors: Replaces mechanical contact burnouts with ultra-fast, wear-free optical trigger sensing.
-
Active Braking System: Stops piston over-travel on single shots and maintains consistent cycle completion.
-
Low-Resistance Wiring Harness: Pre-wired with high-spec heat-resistant wiring and a high-current Deans connector.
-
Smart Electrical Safeguards: Protects against short circuits, over-current spikes, and LiPo battery drain.
-
Programmable Modes: Supports various fire selector modes (semi, binary, burst, and auto depending on firmware version/app connectivity).
Installation & Compatibility Guidance
This MOSFET is designed for Version 2 rear-wired gearboxes found in the CYMA Platinum M4 / Daniel Defense series (specifically CM.1050 / CM.1050DL models). Installation requires opening the Version 2 gearbox shell, removing the old board/trigger setup, and properly aligning the optical sensors with the sector gear selector cam and trigger blade. Basic soldering may be required if connecting custom motor tabs or rear harness extensions.
| SKU | 511731 |
|---|---|
| Brand | Cyma |
| Weapon Category | Parts |
Our courier partners deliver from Monday to Friday, excluding Bank Holidays. We will attempt to dispatch all packages within 24 hours, although at peak times this may take slightly longer. Orders with products with two-tone service or Defence Check may take longer to dispatch.
Once the order is dispatched you will get an email with the tracking number and which courier partner it’s going to be delivered via. Any missing/incorrect items need to be reported with 48hrs of signed delivery.
Click Here to Download the Returns Form (PDF Format)
Faulty Product?! Unfortunately that is part of life but be rest assured we are here to help! Contact one of our friendly staff via phone or email. Stating what the problem is, if we can resolve the problem via phone or email great if not then they will advise how to send it back and what details we require.
The gun will be sprayed 51% in a bright/primary color (we do only blue, green and red currently). The process of two toning currently runs at 2 working days depending on Drying Time, which is effected by Ambient Temperature and Weather. and currently no express delivery is available for this even if you select it at checkout.